How To Clean Evaporator Coil On Ford F150

When your automobile'south AC evaporator coil gets too dirty, it can adversely affect the performance of your car's Air-conditioning. And then it'southward a must to clean it periodically.

Evaporator roll cleaning is non too complicated. Any car owner tin even easily do it themselves without taking out the entire system. Although it may crave the quick removal of some parts and perhaps drilling a hole, cleaning it tin simply exist done by spraying an AC evaporator whorl cleaner on it and rinsing it.

Read further to know more details on how to make clean evaporator coil without removing it.

Table of Contents

• What Yous Will Demand to Follow this Tutorial
  • one. Screwdriver or Electric Drill
  • ii. Evaporator Coil Cleaner
  • 3. Spray Bottle or Garden Hose
  • iv. Towel, Accident Dryer, or Pilus Dryer
• Footstep past Step Instructions
  • Step i: Remove the Glove Box
  • Step ii: Access the Evaporator Roll
  • Step three: Spray the Cleaner on the Evaporator Whorl Through the Access Signal
  • Stride 4: Rinse the Evaporator Coil
  • Step 5: Dry the Evaporator Coil
  • Step 6: Put Back the Blower Fan or Resistor Cake or Seal the Hole You Drilled
  • Step vii: Put Back the Glove Box
• Conclusion

What Y'all Volition Need to Follow this Tutorial

You will merely demand a few things to achieve a make clean evaporator coil. Meet them below:

ane. Screwdriver or Electric Drill

Cleaning evaporator ringlet without removing it would entail making an admission point from where y'all can make clean the evaporator cadre. There are iii options for doing so.

The starting time two options, which are removing the blower fan and taking out the resistor block, would crave the use of a screwdriver. While the 3rd option, which is creating a hole betwixt the blower fan and evaporator example with an electrical drill, would require an electric drill.

2. Evaporator Coil Cleaner

Almost evaporator curlicue cleaners usually come up in a spray canteen with an boosted hose and are foam-based. The cleaner's spray course along with its additional hose makes applying it easier. And the cleaner's foaming action allows the cleaner to stick to surfaces while information technology effectively works on removing dirt, grease, and debris from the evaporator coil.

iii. Spray Bottle or Garden Hose

For rinsing the evaporator coil, you can employ either a spray canteen or a garden hose. But much caution must be observed if you're going to use the garden hose.

4. Towel, Accident Dryer, or Hair Dryer

A towel, blow dryer, or hairdryer will come in handy for drying the evaporator core.

Stride by Step Instructions

Maintaining the cleanliness of car Air-conditioning evaporator coils isn't also complicated of a task. In that location's no need for car owners to send their car to a detailer, every bit they can easily clean evaporator coils without removing the entire system. Find out how below:

Stride one: Remove the Glove Box

Since in this process, you lot would not be removing the entire system, you volition only remove the glove box. The manner glove boxes are designed varies among the different auto models.

Some glove boxes tin can only easily be removed by opening them upwards, pushing their edges together, and pulling them out. While others would require more steps like detaching a cable at the side that supports the glovebox, detaching arm support at the side, unfastening some screws, etc.

Footstep two: Access the Evaporator Coil

The evaporator scroll can be found by the firewall separating the engine compartment and passenger area. In order for you to clean evaporator coil in machine, you would have to brand a way for you to access the evaporator roll. There are 3 means you tin access the evaporator coil.

The easiest ways to get access to the evaporator coil would be to remove the blower fan. You can do this by disconnecting the final that is attached to the blower motor by pushing the plug inwards and pulling information technology out. And then you lot would unfasten the three screws that secure the blower motor to the dashboard'southward underside.

Or another choice that you could do to get quick access to the evaporator gyre is by removing the resistor block Just a heads upwards when removing the resistor cake, if information technology had been working moments earlier you will practise this task, permit information technology to cool for at least five minutes.

The first pace for removing the resistor block is to disconnect the negative battery cable and when setting it aside, make sure it'due south placed somewhere it won't get in contact with metal. Then unfasten the two screws that hold the resistor cake onto the housing and go along them somewhere rubber to avert losing them.

But if you are still not able to admission the evaporator coil fifty-fifty later on removing either aforementioned parts, what you can do to finally admission the evaporator gyre is to drill a hole measuring ⅜ of an inch between the blower fan and evaporator case.

Just be very careful in doing so to avoid damaging other parts. This third option is a risky job that requires much caution, so this should only exist the final resort when necessary.

Pace three: Spray the Cleaner on the Evaporator Whorl Through the Access Point

Attach to the foam-based evaporator coil cleaner, spray the additional hose and insert the hose through the admission point y'all created. Then thoroughly apply the cleaner to the entire evaporator coil. Permit the evaporator scroll soak in the cleaner for thirty minutes to let the cleaner to have effect on the evaporator whorl.

In one case applied and left to soak the evaporator coil, the cream cleaner volition later on become liquid and menstruum through the drain openings. That would as well assistance get rid of any blockage in the drain.

Step 4: Rinse the Evaporator Roll

The evaporator coil would then be rinsed after the cleaner has done its job with its foaming action. There are two ways you lot can rinse the evaporator roll.

1 is by giving it a light spray simply, using a garden hose. But you lot have to be careful not to let the h2o make full up the inside of your car. You may ask someone to help check on the water.

The other way is by spraying clean water on it using a spray canteen. You lot can exercise this method instead if you don't feel comfy with using a hose.

Step 5: Dry the Evaporator Gyre

To dry the evaporator coil, y'all tin can towel it dry out. Or yous tin can use a blow dryer or hairdryer.

Stride half dozen: Put Back the Blower Fan or Resistor Block or Seal the Hole You Drilled

Later finally finishing cleaning and drying the evaporator coil, it'southward time to put back in identify the blower fan or resistor cake that yous removed earlier to access the evaporator curl. But reattach the plug you lot removed from it then spiral it back in.

Or if you lot accept drilled a hole between the blower fan and evaporator example, you would have to seal the hole with RTV silicone.

Step 7: Put Back the Glove Box

Once the evaporator coil is finally clean and whatever removed function from the dashboard'due south underside has been returned or the hole drilled has been sealed, you can then do the last step. And that is to put back the glove box, which you can simply do by doing the glove box removal in reverse.

Determination

Dirt accumulated on the evaporator ringlet can bear upon your car AC'due south cooling. In order to enjoy the best cooling functioning from your car Air conditioning, ane of the essential maintenance tasks you lot need to do periodically is to make clean the evaporator coil.

Trying to figure out how to make clean evaporator roll without removing the system to do information technology yourself is a smart move. Now you've plant out how, the side by side affair to do is to finally apply the steps shown in this tutorial. But before you do, please give this article a like and share information technology if you institute information technology helpful.

Source: https://www.charmcitycirculator.com/clean-evaporator-coil-without-removing/

Posted by: peytoncourand.blogspot.com

Share this post